AFFRI RSD MAG

AFFRI RSD MAG

฿0.00

Portable hardness tester with magnetic clamping base for Rockwell, Superficial Rockwell, Brinell and Vickers methods. The first portable hardness tester that conforms to ASTM E-18 E-10 E384 and ISO 6508 6507 6506 international hardness standards. RSD MAG is a digital portable hardness tester with a manual drive for an automatic test cycle with hardness direct reading. Thanks to its magnetic clamping base it is possible to perform hardness tests on very bulky samples directly in the production department. 

Brand AFFRI
OR
Description

Details

     

USER FRIENDLY

Pulling one single start lever the hardness result will appear in a few seconds. It is so simple and easy to use that there is no need for any particular preparation by the operator:

  1. Identify the test area and place the hardness tester on the sample, no matter the size or geometry
  2. Locking the base lever the magnet will strongly adhere to the test piece for the entire test cycle
  3. Start the test and in 4 seconds the result will appear on the display scale or dial gauge

Safe clamping on any surface, from round to flat, with self-allignment of the indenter with the measurement axis. This hardness tester ensures the highest accuracy and repeatability at every measurement.

 

         

REPEATABILITY & REPRODUCIBILITY

     

THE AFFRI SYSTEMOLOGY (PAT. AFFRI)

Accurate measurements on the first test, even in extreme conditions, will eliminate the need for repeated tests. The R&R data is at the top of its class.

     

Load forces are generated by a dynamometric load cell wich assures long term accuracy and eliminates problems associated with dead weight systems on traditional testers. Results are not affected by any structural deflection, misalignment or vibration.

         

CLAMPING SYSTEM

     

50 MM OF INDENTER AND CLAMPING HOOD STROKE

Accurate hardness measurements even on unstable, dirty or oily samples. The clamping hood applies constant pressure and prevent from accidentaly samples movements during the test cycle.       The measuring head follows the sample even in case of structural deflection. Easy and fast hardness measurements on different thicknesses without acting on the elevating screw.

 

SOFTWARE

 

The software controls the whole instrument during the entire cycle avoiding operator errors:

 

FROM PORTABLE TO BENCH-TOP

 

To convert the RSD MAG from a portable to regular bench top hardness tester, based on your needs, it can be combined with two different size of stand support, 670H or 460L. This system fully conforms to hardness testing standards and allows testing in laboratory on small pieces and prepared samples without the need uf buying another hardness tester. Hardness measurements will result fast and easy as an AFFRI bench tester including the sample clamping system and the auto compensation of deflection thank's to indenter and clamping hood vertical stroke.


TECHNICAL FEATURE

MODEL

RSDMAG D2

RSDMAG D4

Standards

EN-ISO 6506 / EN-ISO 6508 / ASTM E-18 / ASTM E-10

Indenter and clamping hood stroke

0/50 mm

Preload

RSD: 98.1 N (10 kgf)

RSD: 29.42 N (3 kgf)

Test loads

Rockwell: 588.4 - 980.7 - 1471 N (60 - 100 - 150 kgf) 

Vickers: 98.07 - 980.7 N (10 - 100 kgf)

Brinell: 98.07 - 612.9 - 1226 - 1839 N - On request 2452 N
(10 - 62.5 - 125 - 187.5 kgf - On request 250 kgf)

Superficial Rockwell: 147.1 - 294.2 - 441.3 N (15 - 30 - 45 kgf)

Vickers: 29.42 - 294.2 N (3 - 30 kgf)

Brinell: 153.2 - 294.2 - 306.5 N (15.625 - 30 - 31.2 kgf)

Feasible tests

Rockwell: HRC - HRA - HRD - HRB - HRF - HRG - HRL - HRM - HRR

Superficial Rockwell: HRN + HRT

Brinell (On request): HB30 - HB10 - HB5 - HB2.5 MPa (F/D2)

Vickers (On request) (Only indentation): HV3 - HV10 - HV30 - HV100

Accuracy

Better than 0.5 %

Reviews
5 star
0
4 star
0
3 star
0
2 star
0
1 star
0

Image

Feature

Upsell products