 AFFRI Automatic Rockwell - Brinell |
||
  |
MODEL 33XX MRS SERIES |
|
   |
MODEL 330 PRS SERIES - High speed hardness tester for rapid tests in production departments. A single. initiation executes a complete automatic hardness test including clamping the piece. 1000 tests per hour throughput can be achieved. - Direct readout in Rockwell or Brinell hardness scales ( programmed in Affri factory prior to despatch -others available on request) - Programmable tolerances and electrical data output for rapid testing Piece sorted in 3 catagories Ok - Hi - Lo. - Very easy to integrate into a conveyor line. The auto contact capability with clamping and automatic cycle including long stroke head of the AFFRI® system facilitates integration of the 330 PRS to an existing conveyor line. If required, Affri can design and build a full conveyor line with automatic part handling based on end User specifications. VERY HIGH PERFORMANCE - Unaltered operation even in extreme conditions. A SINGLE INPUT TO START THE AUTOMATIC SEQUENCE without interruption applies the minor and major load and measures the Rockwell indentation automatically. All test operations are managed through a single start command to reduce operator fatigue and to increase test repeatability and accuracy to the maximum. AUTOMATIC CONTACT WITH THE TEST PIECE. The AFFRI® system can perform automatic contact with the test piece surface without moving the piece. It automatically moves the indenter and the measuring system until contact is made, the piece is clamped, the force applied and the indentation is measured automatically using Rockwell, Vickers or Brinell procedures. - The system is capable of measuring accurately even if the test piece deflects up to 50 mm during measurement. This automatic compensation provide accurate results under adverse test conditions. - External source of vibration do not influence the result. - The test piece is CLAMPED AUTOMATICALLY and locked in position before the test force (20 to 400 Kgf) is applied. - The test forces are controlled test by test using a load cell and closed loop Affri system to assure high performance conforming to ISO Standards. - Perfect and effective measurements including the first test due to the AFFRI® system inside - Accuracy is stable in every condition. - No need to be levelled when installed. - It can be utilised by untrained operators – initiate the single start input and wait for the test result. |
|
 |
MODEL 250 MRS SINGLE INITIATION OF COMPLETE OPERATION INCLUDING AUTO CONTACT WITH TEST PIECE - Following initiation by the Start button, the 250 MRS head moves down to reach the test surface in distance multiples of 50 mm as part of the continuous test sequence comprising: - approach to the piece. - clamping of the piece. - indentation. - complete measurement cycle and release of piece. - Meets all laboratory requirements. - Full operation even in presence of vibrations, sudden changes in temperature or dusty environments. - Perfect and effective measurements including the first test. - Insensitive to deflections. - Automatic compensation of deflection up to 50 mm. - The long stroke head permits easy tests on different height components without the need to change the elevating screw position every time. - The head moves down automatically into contact and executes the test cycle - Large range of test loads from 98.1 to 1839N automatic selectable. SIMPLE AND UNIVERSAL - Easy and quick Rockwell, SuperRockwell, Brinell, Vickers measures in a single machine. - Every environmental condition is tolerable: presence of dust, vibration, changes of temperature. - Wide software functions, information guide and Windows icons - Immediate conversions. - Statistics and connection to printer with diagrams and graphs. VERY HIGH PERFORMANCE - Unaltered operation even in extreme conditions: irregular pieces, unfinished pieces, that are raised or misaligned, every kind of support (lifting screw, deformable materials, etc.) presence of impurities (dust, oil, etc.) between the test piece and the support or between the support and the point of the support. |
|
  |
MODEL 330 SERIES SINGLE INITIATION OF COMPLETE OPERATION INCLUDING AUTO CONTACT WITH TEST PIECE - Following initiation by operating the Start lever, the 330 RSD head moves down to reach the test surface in distance multiples of 50 mm as part of the continuous test sequence comprising: - approach to the piece. - clamping of the piece. - indentation. - complete measurement cycle and release of piece. - Does not require elevating screws. - Meets all laboratory requirements. - Full operation even in presence of vibrations, sudden changes in temperature or dusty environments. - Perfect and effective measurements including the first test. - Insensitive to deflections. - Automatic compensation of deflection up to 50 mm. - Large fixed base 330x390 mm for sturdy and stable support of test pieces. Small and large size components up to 2000 Kg weight can be tested. - Accessories can be applied on the table to facilitate the positioning of irregular test pieces. - The long stroke head permits easy tests on different height components without the need to change the elevating screw position every time. - The head moves down automatically into contact and executes the test cycle. - Automatic clamping of test piece surface. - High R. R. better than8. - Large range of test loads (from 98.1 to 1839N). UNLIMITED CONDITIONS OF USE - Every environmental condition is tolerable: presence of dust, vibrations, sudden changes of temperature. - Unaltered operation even in extreme conditions: irregular, unfinished raised or misaligned pieces, every kind of support (lifting screw, deformable materials, etc.) presence of impurities (dust, oil, etc.) between the test piece and the support or between the support and the point of the support. |
|
  |
MODEL 331 SERIES SINGLE INITIATION OF COMPLETE OPERATION INCLUDING AUTO CONTACT WITH TEST PIECE - Following initiation by operating the Start lever, the 270 RSD head moves down to reach the test surface in distance multiples of 50 mm as part of the continuous test sequence comprising: - approach to the piece. - clamping of the piece. - indentation. - complete measurement cycle and release of piece. - Does not require elevating screws. - Meets all laboratory requirements. - Full operation even in presence of vibrations, sudden changes in temperature or dusty environments. - Perfect and effective measurements including the first test - Insensitive to deflections. - Automatic compensation of deflection up to 50 mm. - Slim fixed base permits easy measurement outside rings: impossible with conventional hardness testers. - The long stroke head permits easy tests on different height components without the need to change the elevating screw position every time. - The head moves down automatically into contact and executes the test cycle. - Automatic clamping of test piece surface. - High R. R. better than8. - Large range of test loads (from 98.1 to 1839N). UNLIMITED CONDITION OF USE - Any environmental condition is tolerable: presence of dust, vibrations, sudden changes of temperature. - Unaltered operation even in extreme conditions: irregular, unfinished raised or misaligned pieces, every kind of support (lifting screw, deformable materials, etc.) presence of impurities (dust, oil, etc.) between the test piece and the support or between the support and the point of the support. |
|
  |
MODEL 270 SERIES SINGLE INITIATION OF COMPLETE OPERATION INCLUDING AUTO CONTACT WITH TEST PIECE - Following initiation by operating the Start lever, the 270 RSD head moves down to reach the test surface in distance multiples of 50 mm as part of the continuous test sequence comprising: - approach to the piece. - clamping of the piece. - indentation. - complete measurement cycle and release of piece. - Does not require elevating screws. - Meets all laboratory requirements. - Full operation even in presence of vibrations, sudden changes in temperature or dusty environments. - Perfect and effective measurements including the first test. - Insensitive to deflections. - Automatic compensation of deflection up to 50 mm. - Large fixed base 330x390 mm for sturdy and stable support of test pieces. Small and large size components up to 2000 Kg weight can be tested. - Accessories can be applied on the table to facilitate the positioning of irregular test pieces. - The long stroke head permits easy tests on different height components without the need to change the elevating screw position every time. - The head moves down automatically into contact and executes the test cycle. - Automatic clamping of test piece surface. - High R. R. better than8. - Large range of test loads (from 98.1 to 1839N). UNLIMITED CONDITIONS OF USE - Every environmental condition is tolerable: presence of dust, vibrations, sudden changes of temperature. - Unaltered operation even in extreme conditions: irregular, unfinished raised or misaligned pieces, every kind of support (lifting screw, deformable materials, etc.) presence of impurities (dust, oil, etc.) between the test piece and the support or between the support and the point of the support. |
|
 |
MODEL 250 DRMC |
|
 |
MODEL 206 MX SERIES
A twin fully motorised Hardness Tester. - Performs Rockwell and Brinell Tests in a single machine. - Executes Rockwell and Brinell tests with accurate test force and specific ball indenter. - The depth detector and electronic calculator automatically measure and the Brinell value is shown on the clear LCD display. ADVANCED AFFRI TECHNOLOGY INSIDE OFFERS MODERN SOLUTIONS - The force is created by a dynamometer without requiring oil, shock absorbers and without dead weights as in the obsolete systems of many competitors. - The AFFRI Dynamometer System permits the operator to use the machine with highly accurate results and repeatability even if the machine is not level, inclined or is subject to vibrations . The hardness tester can operate directly next to the production line giving real time quality control. - User friendly software permits the storage of results and calculation of average values. The machine can connect to a printer or a PC to transmit stored data. - A -set-of anvils permits easy tests on round or flat surfaces. - Customised accessories can be provided to meet special requirements. SIMPLE OPERATION: Select load and scale for the correct indenter. Turn the hand wheel to raise the test piece into contact with the indenter and the result will appear automatically. |
|
  |
MODEL 206S SERIES SINGLE INITIATION OF COMPLETE OPERATION INCLUDING AUTO CONTACT WITH TEST PIECE
- Following initiation by operating the Start lever, the 206 SD head moves down to reach the test surface in distance multiples of 50 mm as part of the continuous test sequence comprising: - approach to the piece. - clamping of the piece. - indentation. - complete measurement cycle and release of piece. - Meets all laboratory requirements. - Full operation even in presence of vibrations, sudden changes in temperature or dusty environments. - Perfect and effective measurements including the first test - Insensitive to deflections. - Automatic compensation of deflection up to 50 mm. - A -set-of anvils facilitates the positioning of round and flat samples. - The head goes down automatically to contact and execute test cycle. - Automatic clamping of test piece surface. - High R. R. better than8. - Large range of test loads (from 29.4 to 441N). AUTOMATIC - Automatic load application and selection. - Rapid sequence following indenter contact. - High definition (0.1 HRC). - Graphical illuminated display with high contrast to obtain clear, quick and accurate readings. SIMPLE AND UNIVERSAL - High precision and rapidity of measurement. - Full operation even in presence of vibrations, sudden changes in temperature or dusty environments. - Immediate conversion. - Effective statistics software incorporated with connection to printer or computer in order to supply: diagram, graph, tests list, average, standard deviation. |
|
